1.7.14. Electric equipment
Electronic systems of ignition work with very high power of the category. Do not touch them, it is life-threatening.
Safety locks
The defective safety lock can be distinguished on the burned-down fusible thread. You make replacement of a safety lock only after elimination of a cause of defect.
Box of safety locks
The box of safety locks is located in motor office near a broad tank of cooling liquid.
Cover of a box of the main safety locks for a loop also remove Risfiksiruyte up.
Remove an additional cover.
It is always recommended to have with itself a complete set of safety locks.
Place spare safety locks in a box of safety locks in the place provided for this purpose, to the right of it there is a stripper for replacement of safety locks.
Before replacement of a safety lock switch-off the corresponding switch or switch off ignition.
Install the device for a pulling of safety locks on a safety lock and take out it.
Insert safety locks only of the specified nominal current. Its value is specified on each safety lock and is in addition marked in color, and also designated on a seat in a box of safety locks.
Safety locks and the major chains with safety locks
Color marking and current of safety locks
NOTE
Some electric chains can be protected by several safety locks.
|
ATTENTION
Before replacement of a lamp switch off ignition and the corresponding switch.
|
Replacement of lamps
Take a new lamp only for a socle. Do not take a lamp for glass barehanded, otherwise on glass there are traces of fingers. Dirt accumulates on a reflector and worsens its reflective ability. Remove touch traces with the pure not fibrous fabric impregnated with alcohol.
Replaceable lamp to a podobirayta according to marking on a socle of a defective lamp. Do not exceed the specified power in watts.
Replacement of extreme lamps of the forward block of headlights is made through apertures in a forward wheel niche. For this purpose turn wheels in the necessary party, release a clamp and uncover.
Adjustment of headlights
At regulation of headlights regulation of a tilt angle of headlights has to be established on 0.
In the drawing headlights with separate systems of passing beam 1 (external lamps) and driving beam 2 are represented (internal Pampas).
Replacement of lamps of passing beam
Open and prop up a cowl.
When replacing Pampas on the left side open a cover of a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter. Extend a filling branch pipe of a tank of the device of washing of headlights up.
To turn off a cover to the left and remove it.
Press Pampas for the plug down.
Take out the glow lamp with the plug from the reflector case.
Remove the plug from a socle of lamps.
Insert the plug into the new glow lamp, without touching at the same time glass of Pampas.
Insert a new lamp with the plug so that the fixing ledge entered dredging on a reflector.
Establish and close a protective cap of headlights.
After replacement of a lamp on the left side close a cover of a box of safety locks.
After replacement of a lamp on the right side establish and record a hose on the air filter. Establish into place a filling branch pipe of a tank of the device of washing of headlights.
Replacement of lamps of driving beam
Open and prop up a cowl.
When replacing a lamp on the left side open a koyshka of a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter.
Turn off a cover to the left and remove it.
To disconnect the plug from a lamp.
Release a spring bracket from a fixing ledge forward and turn aside.
Take out the glow lamp from the boss.
At installation of a new lamp insert the fixing ledges into reflector cuts, at the same time not to touch lamp glass.
Record a spring wire bracket, insert the plug into a lamp.
Establish and close a protective cap of headlights.
After replacement of Pampas on the left side close a cover of a box of safety locks.
After replacement of Pampas on the right side establish and record a hose on the air filter.
System of halogen headlights (replacement of lamps of parking light)
Open and prop up a cowl.
When replacing a lamp on the left side open a cover of a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter.
Turn a cap of the high beam headlamp to the left and take off it.
Remove the plug from a lamp of driving beam.
Take out a cartridge of a lamp of parking fire from a reflector.
Take out a lamp from the boss.
Insert a new lamp, without touching at the same time lamp glass.
Insert a cartridge of Pampas into a reflector.
Put on the plug a lamp of driving beam.
Establish and close a protective cap of headlights.
After replacement of Pampas on the left side close a cover of a box of safety locks.
After replacement of a lamp on the right side establish and record a hose on the air filter.
System of halogen headlights (replacement of lamps of forward indexes of turn)
Open and prop up a cowl.
When replacing a lamp on the left side open a cover of a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter. Extend a filling branch pipe of a tank of the device of washing фар* up.
Turn to the left and exempt a cartridge of a lamp from a clamp.
Slightly press a lamp in a cartridge, turn to the left and take out it.
Insert a new lamp, without touching at the same time lamp glass.
Record a cartridge in a reflector, having turned it to the right.
After replacement of a lamp on the left side close a cover of a box of safety locks.
After replacement of a lamp on the right side establish and record a hose on the air filter. Establish into place a filling branch pipe of a tank of the device of washing of headlights.
System of ellipsoidal headlights (replacement of lamps of the neighbor light)
Open and prop up a cowl.
When replacing a lamp on the left side open a cover of a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter. Extend a filling branch pipe of a tank of the device of washing of headlights up.
Take off a headlight cap for what press a clamp and extend a cap down.
To disconnect the plug from a lamp.
Remove a spring bracket from a fixing ledge and to turn off it aside.
Take out the glow lamp from the boss.
At installation of a new lamp insert the fixing ledges into reflector cuts, at the same time not to touch lamp glass.
Record a spring wire bracket, insert the plug into a lamp.
Establish and close a protective cap of headlights.
After replacement of a lamp on the left side close a cover of a box of safety locks.
After replacement of Pampas on the right side establish and record a hose on the air filter. Establish into place a filling branch pipe of a tank of the device of washing of headlights.
System of ellipsoidal headlights (zamn of lamps of forward indexes of turn)
Open and prop up a cowl.
When replacing a lamp on the left side open a cover of a box of safety locks. On cars with the Z 13 DT engine besides take out from directing relay the box located before a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter.
Turn to the left and exempt a cartridge of a lamp from a clamp.
Slightly press Pampas in a cartridge, turn to the left and take out it.
Insert a new lamp, without touching at the same time lamp glass.
Record a cartridge in a reflector, having turned it to the right.
After replacement of Pampas on the left side close a cover of a box of safety locks. On cars with the Z 13 DT engine besides establish into place and record in the relays directing a box.
After replacement of a lamp on the right side establish and record a hose on the air filter.
System of xenon headlights (replacement of lamps of passing beam)
Passing beam of xenon headlights works at very high voltage. Do not touch, it is life-threatening. It is recommended to charge replacement of lamps to the partner of Opel.
System of xenon headlights (replacement of lamps of forward indexes of turn)
Open and prop up a cowl.
When replacing a lamp on the left side open a cover of a box of safety locks. On cars with the Z 13 DT engine besides take out from directing relay the box located before a box of safety locks.
When replacing a lamp on the right side remove a hose from the air filter.
Turn to the left and exempt a cartridge of a lamp from a clamp.
Slightly press Pampas in a cartridge, turn to the left and take out it.
Insert a new lamp, without touching at the same time lamp glass.
Record a cartridge in a reflector, having turned it to the right.
After replacement of a lamp on the left side close a cover of a box of safety locks. On cars with the Z 13 DT engine besides establish into place and record in the relays directing a box.
After replacement of Pampas on the right side establish and record a hose on the air filter.
Indexes of turn, brake fires, back marker lights and headlights of a backing (Corsa)
Unscrew the screw-driver both screws on the lamp case.
Take out the lamp case from clamps down.
Disconnect the cable plug by means of the screw-driver and remove from the holder of a lamp.
Unscrew the screw-driver four screws on the holder of a lamp. Remove the holder of a lamp from the lamp case.
Lamps from top to down: lamp of the index of turn lamp of back fire / lamp of brake fire backing lamp
Take out a lamp from the boss.
Insert a new lamp, without touching at the same time lamp glass, install the holder of a lamp in the case of a lamp and to screw densely screws, fix the cable plug, insert the lamp case with the fixing pins into a body and fix.
Brake fires, back fires, indexes of turn, backing headlight, back fog lights (Combo)
Having pressed locking uvulas, to a rasfiksiruyta also remove the closing cover.
Remove the cable plug from the holder памп.
Holding the case of lamps outside, to weaken by means of a key for wheel bolts both fixing nuts and unscrew manually.
Remove the case of lamps.
Squeeze to each other lock uvulas on the holder of lamps, take out the holder of lamps, as shown in the drawing.
Lamps from top to down: lamp of back fire / lamp of brake fire, lamp of the index of turn, backing lamp, lamp of a back fog light.
Take out Pampas from the boss.
Insert the new glow lamp, without touching at the same time lamp glass. Record the holder of lamps in the case. Insert the case of lamps into a car body. To screw fixing nuts manually on carving hairpins and to tighten densely. Insert the cable plug. Establish a cover and close.
Special execution for the certain countries: back fog lamp only on the left side.
Illumination of registration plate (Corsa)
Insert the screw-driver on the right vertically at the lamp case, press to the right and unblock a spring. Take out the case of Pampas, having given it down.
Turn to the left and exempt a cartridge of a lamp from a clamp.
Take out a lamp from the boss.
Insert a new lamp, without touching at the same time lamp glass.
Turn a cartridge of a lamp to the right and record it. Insert the case of a lamp and to fix it.
Combo
Unscrew both screws. Take out a cartridge of a lamp.
Slightly press a lamp in the direction of the spring plug and take out a lamp.
Insert a new lamp, without touching at the same time lamp glass.
Insert a cartridge of a lamp and to fix by means of the screw-driver.
Lighting lamps of salon, lamp for reading behind, luggage carrier lighting lamps
To cut off power the lamp, before its dismantle close doors or hold pressed the trailer switch.
Squeeze out a lamp the screw-driver and take out.
Slightly press a lamp in the direction of the spring plug and take out a lamp.
Insert a new lamp, without touching at the same time lamp glass.
Insert a lamp into an opening and record.
Lighting lamps of salon in front and lamps for reading
To cut off power the lamp, before its dismantle close doors.
Squeeze out reflector glass from the case.
Take out a lamp from the boss.
Insert a new lamp.
Establish and record reflector glass.