d5bc60b9




4.5.4. Removal and installation of the back shock-absorber

NOTE
Shock-absorbers act and installed only one by one from each party of the car.

NOTE
Further removal and assembly on the one hand is described. Works on other party are performed similarly. Quenchers of blow are replaced only with couples. When replacing shock-absorbers it is necessary to use service details, the corresponding versions of the car and to its equipment.

Removal
Lift the car.

NOTE
Use the points of raising of the car provided for this purpose.

Remove the shock-absorber 5.
Uncover 1 a shock-absorber cap.
Turn out a nut 2 from the shock-absorber.

NOTE
Hold an open wrench for the flattened places of a rod of the piston of the shock-absorber.

Remove an adjusting disk 3 and rubber depreciation laying 4 from a piston rod.

NOTE
You monitor the adjusting provision.

Remove the shock-absorber.

Installation
Install the shock-absorber 1 on the back bridge.
Level the shock-absorber concerning an opening on a blow quencher cap.
Tighten the screw.
Basic design (M10x1,25 screw): 65 N · m.
Litoy Bridge with a lever suspension bracket (M14 x 1,5 screw): 110 N · m.
Lower the car.
Remove a shock-absorber piston rod in an opening on a shock-absorber cap.
Put on rubber depreciation consolidation 4 and an adjusting disk 3 a piston rod.

NOTE
You monitor the adjusting provision.

Tighten a new nut of 2-20 N · m.

NOTE
Hold an open wrench for the flattened places of a rod of the piston of the shock-absorber.

Put on a cover 5 a shock-absorber cap.
Removal and installation of the back springs damping Kolya above and an intermediate ring of a saddle of a spring below

NOTE
Back springs act and established only one by one from each party of the car.

NOTE
Further it is described removal and assembly on the one hand. Works on other party are performed similarly. Back springs are replaced only with couples. When replacing back springs it is necessary use service details, the corresponding versions of the car and to its equipment.

Removal

NOTE
Use the points of raising of the car provided for this purpose.

Lift the car.
Remove system of levers of the sensor of a chain of regulation of a tilt angle of headlights from the holder on the back bridge.

NOTE
On cars with xenon headlights.

Remove back springs 4.
Prop up the back bridge a hydraulic jack on the party of assembly under the longitudinal lever of a suspension bracket 2.
Turn out the screw of 1 shock-absorber on the back bridge.
At cars with the cast bridge with a lever suspension bracket: remove a fixing ear of the shock-absorber 3 from the back bridge (shooter).
Slowly lower and remove a hydraulic jack.
From assembly to delay the back bridge down so (shooter) that the back spring could be removed.

NOTE
You monitor the adjusting provision of springs.

Remove the damping ring above 1 and an intermediate ring of a saddle of a spring below 2 in the bottom of the car or a clip at the back bridge.

Installation
Establish the damping ring above 1 and an intermediate ring of a saddle of a spring below 2 in the bottom of the car or a clip at the back bridge.
Insert a back spring.

NOTE
You monitor the adjusting provision of back springs.

From assembly delay the back bridge down so (shooter) that the back spring could be inserted.

NOTE
Establish the party of a spring with larger opening on a spring nest disk below on the back bridge.

Establish the back bridge in the necessary situation.
Reinstall a hydraulic jack on the party of assembly under the longitudinal lever of a suspension bracket 3 back bridges.
Lift the back bridge to situation for installation of the shock-absorber 2 on the back bridge.
Install the shock-absorber on the back bridge. Tighten the screw 1.
Basic design (M10 x 1,25 screw): 65 N · m.
Litoy Bridge with a lever suspension bracket (M14kh 1,5 screw): 110 N · m.
Remove a hydraulic jack.
Install system of levers of the sensor of a chain of regulation of a tilt angle of headlights on the holder on the back bridge: 5 N · m.

NOTE
On cars with xenon headlights.